3d Embossed Fabric Supplier Introduces The Techniques Of Dyeing Fabric
Folk dyeing workshops are mostly open-air operations. The main equipment includes cooking stoves, large tanks, urn boards, cloth-rolling stones, cloth rolls, cloth racks, twist boards, urn sticks, and watch bowls. Below,3d Embossed Fabric Supplier introduces the rules of dyeing fabric:
1. Pot stove
Generally, there are many basement wind stoves, and the ventilation ducts under the stove are relatively high, so there is no need for blasting. The height of the stove is about 80 cm, which is convenient for workers to operate. Two large pots are placed in front and back, usually 16 printed pots. The front pot near the stove door is used for cooking cloth; the back pot near the chimney is used for warm water.
2. Big tank
Prepare a large vat with several ports, which is commonly referred to as a dye vat, used for soaking dyeing and filtering cloth. Put a wooden board on each cylinder, called the cylinder board. Remove the cloth from the dyeing vat and place it on the vat to drain. A smooth wooden pile is buried behind the tank, the cloth or thread after water control is put on the wooden pile, and a short wooden stick is inserted into it and twisted to remove the water.
3. Grinding cloth stone
It is also called kick cloth stone. It is generally carved from cotton stone, with both ends tilted up, and the bottom surface is smooth, resembling ingots. It is about 3 feet long, 2 feet high, and 1 foot thick. Compatible with cloth rollers for cloth rolling. The floor of the cloth-grinding place is flattened with smooth slate or wooden boards, and a wooden frame supported by the cloth-grinding person is installed.
4. Cloth roll
It is a cylinder made of hardwood, approximately 2.5 feet long and 3.5 inches in diameter. Jidong generally uses Muyu, Dumu or Jujube.
5. Drying rack
It is built with pine poles or bamboo poles. The length and width depend on the site, and the height is generally about 4 meters. It is used to dry printed and dyed cloth.
6. Twisted board
It is carved into several layers of unedged paper which are bonded together and used for printing and dyeing hemp cloth. Several sets are generally available. Separately prepare a cylinder stick and a watch cylinder bowl.
Through the above introduction, Custom Embossed Fabric Manufacturers hopes that you can simply refer to the content of this article in future use.
https://www.haiwei-hometextile.com
Folk dyeing workshops are mostly open-air operations. The main equipment includes cooking stoves, large tanks, urn boards, cloth-rolling stones, cloth rolls, cloth racks, twist boards, urn sticks, and watch bowls. Below,3d Embossed Fabric Supplier introduces the rules of dyeing fabric:
1. Pot stove
Generally, there are many basement wind stoves, and the ventilation ducts under the stove are relatively high, so there is no need for blasting. The height of the stove is about 80 cm, which is convenient for workers to operate. Two large pots are placed in front and back, usually 16 printed pots. The front pot near the stove door is used for cooking cloth; the back pot near the chimney is used for warm water.
2. Big tank
Prepare a large vat with several ports, which is commonly referred to as a dye vat, used for soaking dyeing and filtering cloth. Put a wooden board on each cylinder, called the cylinder board. Remove the cloth from the dyeing vat and place it on the vat to drain. A smooth wooden pile is buried behind the tank, the cloth or thread after water control is put on the wooden pile, and a short wooden stick is inserted into it and twisted to remove the water.
3. Grinding cloth stone
It is also called kick cloth stone. It is generally carved from cotton stone, with both ends tilted up, and the bottom surface is smooth, resembling ingots. It is about 3 feet long, 2 feet high, and 1 foot thick. Compatible with cloth rollers for cloth rolling. The floor of the cloth-grinding place is flattened with smooth slate or wooden boards, and a wooden frame supported by the cloth-grinding person is installed.
4. Cloth roll
It is a cylinder made of hardwood, approximately 2.5 feet long and 3.5 inches in diameter. Jidong generally uses Muyu, Dumu or Jujube.
5. Drying rack
It is built with pine poles or bamboo poles. The length and width depend on the site, and the height is generally about 4 meters. It is used to dry printed and dyed cloth.
6. Twisted board
It is carved into several layers of unedged paper which are bonded together and used for printing and dyeing hemp cloth. Several sets are generally available. Separately prepare a cylinder stick and a watch cylinder bowl.
Through the above introduction, Custom Embossed Fabric Manufacturers hopes that you can simply refer to the content of this article in future use.
https://www.haiwei-hometextile.com
3d Embossed Fabric Supplier Introduces The Techniques Of Dyeing Fabric
Folk dyeing workshops are mostly open-air operations. The main equipment includes cooking stoves, large tanks, urn boards, cloth-rolling stones, cloth rolls, cloth racks, twist boards, urn sticks, and watch bowls. Below,3d Embossed Fabric Supplier introduces the rules of dyeing fabric:
1. Pot stove
Generally, there are many basement wind stoves, and the ventilation ducts under the stove are relatively high, so there is no need for blasting. The height of the stove is about 80 cm, which is convenient for workers to operate. Two large pots are placed in front and back, usually 16 printed pots. The front pot near the stove door is used for cooking cloth; the back pot near the chimney is used for warm water.
2. Big tank
Prepare a large vat with several ports, which is commonly referred to as a dye vat, used for soaking dyeing and filtering cloth. Put a wooden board on each cylinder, called the cylinder board. Remove the cloth from the dyeing vat and place it on the vat to drain. A smooth wooden pile is buried behind the tank, the cloth or thread after water control is put on the wooden pile, and a short wooden stick is inserted into it and twisted to remove the water.
3. Grinding cloth stone
It is also called kick cloth stone. It is generally carved from cotton stone, with both ends tilted up, and the bottom surface is smooth, resembling ingots. It is about 3 feet long, 2 feet high, and 1 foot thick. Compatible with cloth rollers for cloth rolling. The floor of the cloth-grinding place is flattened with smooth slate or wooden boards, and a wooden frame supported by the cloth-grinding person is installed.
4. Cloth roll
It is a cylinder made of hardwood, approximately 2.5 feet long and 3.5 inches in diameter. Jidong generally uses Muyu, Dumu or Jujube.
5. Drying rack
It is built with pine poles or bamboo poles. The length and width depend on the site, and the height is generally about 4 meters. It is used to dry printed and dyed cloth.
6. Twisted board
It is carved into several layers of unedged paper which are bonded together and used for printing and dyeing hemp cloth. Several sets are generally available. Separately prepare a cylinder stick and a watch cylinder bowl.
Through the above introduction, Custom Embossed Fabric Manufacturers hopes that you can simply refer to the content of this article in future use.
https://www.haiwei-hometextile.com
0 Reacties
0 Deel acties