Aluminum Lamp Housing Supplier Introduces The Installation Process Of Indoor Lighting
2022-7-7
Aluminum Lamp Housing Supplier introduces the method of installing indoor lighting:

1. When setting the installation plan, we must first notice that if we want to install the lamp successfully, we must check in advance whether its accessories are complete and whether there are any defects.

2. Know the place for each lamp to be installed according to its purpose. Chandeliers and ceiling lights should be installed in a large room, such as the living room, while wall lights and downlights should be installed in small rooms such as bedrooms and bathrooms so that the effect will be better.

3. You can choose a variety of lighting colors, whether it is bright or dark, as long as it meets your aesthetics and allows romance and fashion to fill the space, it is a good installation choice. The appearance of the lamps is also the same, allowing the designer to help you decide.

4. When installing electrical lighting fixtures, screws, hooks, and other fixtures should be used for tight fixation.

5. If the position of the lamp is less than 2.4 meters from the ground, the voltage used cannot be greater than 36 volts, and the surface of the lamp must be insulated.


Through the above introduction,High Lumen Street Light Housing Manufacturers hopes that you can simply refer to the content of this article in future use.


https://www.cnledstreetlight.com/

Aluminum Lamp Housing Supplier Introduces The Selection Process Of Street Lamp Housing

2022-6-15

The use of LED street lights is becoming more and more widespread. Except for the LED lighting technology, the rest are LED street light housings. Below,Aluminum Lamp Housing Supplier will introduce the precautions for purchasing LED street light housings:

When purchasing an LED street lamp housing, we should first clarify the power that the LED lamp needs to dissipate. Generally speaking, some parameters for the heat sink should be provided, such as the specific heat of metal, the thermal conductivity of metal, the thermal resistance of the chip, the thermal resistance of the radiator, the thermal resistance of the surrounding air, etc. Then determine the type of heat dissipation, natural convection heat dissipation,strong wind cooling, heat pipe heat dissipation, and other heat dissipation methods. Compared with natural convection, the cost of heat dissipation is low, the cost of strong wind cooling is medium, the cost of heat pipe heat dissipation is relatively high, and the cost of air-jet cooling is high.

When choosing the LED street lamp housing, you should also determine the high operating temperature permitted by the LED lamp (ambient temperature plus the permitted temperature rise of the lamp). In this regard, attention should be paid to combining the radiator and the LED lamp into a complete lamp, and powering it for more than eight hours. Check the temperature of the luminaire at a room temperature of 39℃--40℃ to see if it meets the heat dissipation requirements to verify whether the calculation is correct. If it does not meet the conditions of use, recalculate and adjust the parameters. The sealing of the radiator and the lampshade of the LED street lamp housing should be waterproof and dustproof. The anti-aging rubber pad or silicon rubber pad should be placed between the lampshade and the radiator, and the stainless steel bolt should be used to fasten it to ensure the seal is waterproof and dustproof.

The heat dissipation aspect of the LED street lamp housing determines the use time and lifespan of the LED street lamp. Therefore, you must pay more attention when choosing the LED street lamp housing, because it is related to its service life. If it can not dissipate heat well, it will be a disaster for the LED street lamp.

Through the above introduction,High Lumen Street Light Housing Manufacturers hopes that you can simply refer to the content of this article in future use.

www.cnledstreetlight.com

Aluminum Lamp Housing Suppliers Introduce Tips For Using Die-cast Linear Lamp Housings

2022-4-11

Aluminum Lamp Housing Suppliers introduces the matters needing attention in the process of using die-cast linear lamp housing:

1. If there are multiple core-pulling positions, we should release the two sides, but do not let go of the lower core-pulling, which will cause problems with the core-pulling during the finalizing process.

2. The pressure of the die-casting machine should be considered, and the pressure should be controlled so as not to damage the mold and cause unnecessary damage to the production process.

3. In the process of die-casting of the linear lamp shell, the suitability of aluminum alloy and die-casting needs to be controlled, the main melting time and die-casting time and temperature are required, and more importantly, the effect of process parameters on the quality of castings.

4. Considering the thickness of the die-casting wall of the linear lamp housing, too thick thickness will make it difficult to fill.

5. During the die-casting process of the linear lamp shell, we need to consider the complex structure of the mold and do not easily pull out multiple cores to avoid damage to the crafts.

Through the above introduction, China 100w Street Light Housing Factory hopes that you can simply refer to the content of this article in future use.
https://www.cnledstreetlight.com/